Any Eper buffs?
- Thread starter GhostWKD
- Start date
Currently reading:
Any Eper buffs?
Think I have a spare TB sat on my floor if you can wait till stanford and bring a tenner? 
OP
OP
dont need a tb just unused gaskets and bolts think its the cause of my slight boost leak
just unused gaskets and bolts think its the cause of my slight boost leak
GhostWKD said:dont need a tb
Well the TB has both of those bits.. also may have some in my parts box but if you want to buy new fine
OP
OP
nah wanna get fresh ones thx anyway tho fella
thx anyway tho fella 
Hang on a sec.
Liam
Liam
this was all covered on msn hours ago liambloomfieldliam said:
OP
OP
dunno was you afterall Lol
Part codes i think:
big spacer bit - 46405881 (Is this for the bit between the top and bottom half of tb btw custard?)
7738332 shown as screw and washer ass for those big rods?
Lol Part codes i think:
big spacer bit - 46405881 (Is this for the bit between the top and bottom half of tb btw custard?)
7738332 shown as screw and washer ass for those big rods?
Threaded rod 7786326 £2
Nuts 60809794 £0.50
What gasket do you mean, the one with all the cut outs?
Liam
Nuts 60809794 £0.50
What gasket do you mean, the one with all the cut outs?
Liam
OP
OP
is the gasket for inbetween the top and bottom half of the tb, like a orangey colour iirc? (not that epers in colour, but you may remember seeing one? )
)
custard boy said:this was all covered on msn hours ago liam
Someone should update the thread then!
Liam
OP
OP
GhostWKD said:dunno was you afterall
Part codes i think:
big spacer bit - 46405881 (Is this for the bit between the top and bottom half of tb btw custard?)
7738332 shown as screw and washer ass for those big rods?
can anyone check those part numbers at all?
Couldnt remember but apparently there is 2 bolts through the TB into the inlet, and then the rods out of TB to the plenum top? so need 2 seperate part numbers (parts guy wasnt sure of these lol
) and the spacer, parts guy seemed to think that part number was for the spacer that sits inbetween tb and the inlet manifold, but i need the cork spacer type thing that goes inbetween the 2 halves of the throttle body...
need the spacer that sits on top of this bit;
https://www.fiatforum.com/attachment.php?attachmentid=3957&d=1112292865
pleaseeee help if you can, need to get my bits sorted so i can re-fit this TB and pray it fixes my prob
OP
OP
sorted i think he has to order it all in though he'll get it on sat and send it out to me then yay
he has to order it all in though he'll get it on sat and send it out to me then yay
OP
OP
or not on backorder with no date
on backorder with no date Donny XP
New member
Donny XP
New member
its from DVD, but when i try to run it it opens internet explorer to the page:
http://127.0.0.1:7080/navi?KEY=STARTUP
but its blank, theres a little eper icon on the taskbar which says "Server Stared" and has a tick next to it but all i'm getting is a blank page and i need it to work :bang:
i've tried changing the ports to the 3 other lised but that didnt work either, and eper dont have a troubleshooting section
please help!
lol
Donny
http://127.0.0.1:7080/navi?KEY=STARTUP
but its blank, theres a little eper icon on the taskbar which says "Server Stared" and has a tick next to it but all i'm getting is a blank page and i need it to work :bang:
i've tried changing the ports to the 3 other lised but that didnt work either, and eper dont have a troubleshooting section
please help!
lol
Donny
Donny XP
New member
i've tried firefox and opera, nothin going its well weird, is there anyway it could be the ports? considering i am predicted an A at A-Level computing i suck at this....
