Hello to everyone, it's going to be a longer post but bare with me. A few months ago the car developed a concerning knocking noise from the front right side. As a pretty competent diy-er, I immediatley checked the usual stuff, tightened the wheels, checked the bearings, exhaust hangers etc. After it didn't went away I got to work. Checked and/or replaced everything; drop links, ball joints, dissasembled the struts, replaced the engine and gearbox mounts, everything. The noise can be described as someone hitting the subframe with a hammer (checked the subframe bolts). Also did the brakes the other day and everything is ok. Now for the plot twist, when I lift the front end of the car with a jack, je the noise goes away for a few days then gradually comes back!! Now if anyone has got any idea what to check next, I would really appriciate it. The car is a 2011 Bravo sport 1.4 t-jet 88kw with 120000 km. Thank you in advance
Technical Knocking noise problem
- Thread starter noDi
- Start date
- Replies 25
- Views 802
Currently reading:
Technical
Knocking noise problem
Sure, checked both mounts, they look fairly new...
Torsion bar at the ends bushes of torsion bar. Check and remove the reinforcement bar = the metal strip where the left and right protection undertrays are fixed with 2 screws.
Not sure I understand, the steel bracket is making noise?
- Joined
- Feb 28, 2016
- Messages
- 1,026
- Points
- 276
I suspect the rubber bushes at the rear of the arms. You jack up and they twist when lowering they go back in a different position until it then drives and begins to settle back.
Sadly you only describe a knocking noise but not describing any times movements when noises happen to help the diagnosis. As this is really helpful
Sadly you only describe a knocking noise but not describing any times movements when noises happen to help the diagnosis. As this is really helpful
You mean the arb bushes? I suspected them but they look ok and the arb doesn't move when I try tensioning it with a crowbar. The knocking occurs over large bumps but also uneven sections of the road ( for example where the asphalt sinked somewhat ).
- Joined
- Feb 28, 2016
- Messages
- 1,026
- Points
- 276
ARB in my book says anti roll bar. My description is the bushes at the rear of the main lower arm
Sorry, wasn't reading with comprehension...I guess I will remove the arms and inspect because they don't look bad, but tbf you cant see the whole bush
- Joined
- Feb 28, 2016
- Messages
- 1,026
- Points
- 276
Look for contact marks on the perimeter arround the arm. No real need to remove them. If you have banging then there will be contact marks
Thank you, that's really helpfull. Will report back
Yes, if it is deformed at the ends or is not tightened well in the screws.
Did you do some work, put some new parts before noise started? Something on exhaust maybe?
Can you take a video of it doing the noise?
Can you take a video of it doing the noise?
Also, you said it's on the front right side.
Is it the engine?!
Is it the engine?!
All the mounts are new, I will try to record it
Not the mounts. The engine! Like piston slap, rod knock, main bearing wear, wrist pin (gudgeon pin) wear.
Timing chain or tensioner issues if it has a chain, not belt.
And of course, it could also be detonation knocking (combustion knock).
The Panda Nut
Nutty about Pandas Infected by Panda virus and OPD
I would say drop liks on the strut / ATRB and dont think because you cant move them they wont knock.
Also dont be mislead into ruling out all ther sources other than suspension. Check for air cleaner box, raidator mounts and bumpers. These noises can be devilish to pin down.
Broken spring or stone caught in the spring tray.
Also dont be mislead into ruling out all ther sources other than suspension. Check for air cleaner box, raidator mounts and bumpers. These noises can be devilish to pin down.
Broken spring or stone caught in the spring tray.
Last edited:
- Joined
- Feb 28, 2016
- Messages
- 1,026
- Points
- 276
Im going to ask again. When do you get the noise( i dont mean 3 days after jacking it up).
Is the noise when going straight or on corners,when going over speed bumps, when accelerating or braking, when changing gear. When engaging clutch.
This is basic information that is REALLY helpful to assist every one who is trying to help you. The only description yoh have given is "knocking drivers side front". Very vague.
Help everyone who is trying to help you!
Is the noise when going straight or on corners,when going over speed bumps, when accelerating or braking, when changing gear. When engaging clutch.
This is basic information that is REALLY helpful to assist every one who is trying to help you. The only description yoh have given is "knocking drivers side front". Very vague.
Help everyone who is trying to help you!
Sorry for not posting for a while but the noise just came back few days ago. Meanwhile i rechecked everything again with the car on the ground, can't find any evidence of excessive control arm movement, bushes seem really solid. Here's a video of driving maybe 20-30 kph on really bad asphalt with lots of patches.
- Joined
- Feb 28, 2016
- Messages
- 1,026
- Points
- 276
It seems more obvious when going in a straight line so it suggests anti roll bar in some way. At road height does there seem to be reduced clearance between the arms and anti roll bar
