Rolling Road Day North of London Near M1 on a sunday

[dave]

got one of them blue conecting right angle pipes in my pocket

 

[H2DaE]

Singh, here's the vid i took of your car on the RR

https://www.fiatforum.com/gallery/showphoto.php?photo=38962

Here's an F360 which had a little too much oil for breakfast

https://www.fiatforum.com/gallery/showphoto.php?photo=38963

Here's me on the RR

https://www.fiatforum.com/gallery/showphoto.php?photo=38964

 

[puntokris]

Was a good day as usual.

Apart fromt he fact my maf housing is still not right, and I need a new turbo

 

[ChrisUK]

Was a good day as usual.

Apart fromt he fact my maf housing is still not right, and I need a new turbo

New turbo?!?! , Don't say you got one from the bad batch!.

 

[adamcot]

adamcot, I noticed that aswell. Love it. How much power you get after you fitted the kit?

Its now running at 121 bhp, considering its meant to have 103 bhp standard (rolled before fitting the kit at 111 bhp!!) No other modifications either You can really feel the difference, had a right giggle on the way home yesterday and on the way to work today :slayer:

 

[puntokris]

New turbo?!?! , Don't say you got one from the bad batch!.

Yep looks like it. Plenty of oil being shot out and nice exhaust fumes coming from the rear of the engine bay. So unfortunately no map could be loaded. Good times!

 

[H2DaE]

Was a good day as usual.

Apart fromt he fact my maf housing is still not right, and I need a new turbo

Did you guys figure out which way the MAF went on?

 

[puntokris]

Did you guys figure out which way the MAF went on?

Yea but I need to cut down the kit where the maf sits to get it a few cm down into the pipe to get a better reading. I also need to seal it properly and then see if it works.

 

[Slosei]

Any power graphs please lol

 

[adamcot]

Here we go, before and after over-layed onto one graph! first time completely standard, second with GSR induction

 

[Memzee]

I forgot to get mine... Peter and the red dot guy seemed to be quite impressed though.

 

[Oldschool]

I forgot to get mine... Peter and the red dot guy seemed to be quite impressed though.

Come by sometime and you will get the printout.

 

[Steely]

soo got to get mine on the rollers

 

[puntokris]

Forgot to get my printout but I ran a 188bhp run and I didin't even find out the torque :bang:

 

[adamcot]

Forgot to get my printout but I ran a 188bhp run and I didin't even find out the torque :bang:

Well im only 65 bhp behind you

 

[Thewitt]

how come your enginemanagment light is allways coming on?
you know what the issue is or?

Its because of my supersprint manifold and me running with both lambda probes pre cat for a few months.
Now Ive got it set up as it should be with one lambda pre cat and one lambda post cat, the post cat lambda is reading too high which makes me believe that the cat has had it and will be an expensive fix if I go for a genuine supersprint item.

 

[dave]

is your pre cat lambda in the manifold or front pipe?

 

[Oldschool]

is your pre cat lambda in the manifold or front pipe?

Or are they the wrong way round?

 

[ChrisUK]

I forgot to get mine... Peter and the red dot guy seemed to be quite impressed though.

He always is with the 1.4 sportings , the GSR works wonders. I had 103bhp standard .

 

[Singh!]

Singh!, did you get your map done aswell? Up to 100 now?

No, its at 93hp atm but the torque comes in a lot earlier and has gone up by 10 to 82
Need to speek to peter to see what i can do to get it up to 100bhp without sending all the torque to the high rev range.

I went down to red dot again today and they have told me that my oxygen sensor has gone (1st one).. so ive gtta get that sorted before i do anything else