Just noticed on my Panda the passenger side arch and bumper weren't lining up properly. I can move them back in position but it won't stay where it should.

On closer inspection it appears to have a clip missing which aligns the plastics. I still have one on the other side as pictured.

Would anyone know a part number for this? Can't find one anywhere online unfortunately

Try- Shop4parts. They are very helpful

Interesting to know there is an actual clip. I just thought it was fiat fitment and it was meant to be a bit wonky!

Let us know if you find where to get one from.

They are the usual bullet shaped trip clips. To remove the spats, go behind and squeeze the clip. It will compress slightly and push through the panel.

https://www.ebay.co.uk/itm/10X-TRIM-LINING-PANEL-CLIPS-BUMPER-WINDOW-BOOT-DOOR-BODY-CAR-FIAT/333272433185?fits=Car+Make%3AFiat&hash=item4d9895c221:g:3UQAAOSwFnFV9TM-

You can also use low height stainless button head M5 screws with a 20mm washer. Hold the screw thread with pliers while you run down a nyloc nut. No need to tighten it - just take it until the trim is nipped.

DaveMcT said:

They are the usual bullet shaped trip clips. To remove the spats, go behind and squeeze the clip. It will compress slightly and push through the panel.

https://www.ebay.co.uk/itm/10X-TRIM-LINING-PANEL-CLIPS-BUMPER-WINDOW-BOOT-DOOR-BODY-CAR-FIAT/333272433185?fits=Car+Make%3AFiat&hash=item4d9895c221:g:3UQAAOSwFnFV9TM-

You can also use low height stainless button head M5 screws with a 20mm washer. Hold the screw thread with pliers while you run down a nyloc nut. No need to tighten it - just take it until the trim is nipped.

Click to expand...

Please read the post. This is not related to the clips you reference. These are different clips altogether as per the picture.

dac69er said:

Please read the post. This is not related to the clips you reference. These are different clips altogether as per the picture.

Click to expand...

There is no clip in there. The bumper arch clips under the wing arch. That's it. So to you

There is a tag on the bumper arch spat that carries the wheel arch liner. It does not retain the spat.

Well I have a clip there as pictured, can't imagine it's something fitted as an after thought as it fits so well

I may well make something up myself if I can

The bumper top edge fits under the wing with two M6 bolts.

The bumper spat is fixed to the bumper with three bullet shape clips. The wing spat is similar. The spat ends fit together. There is no clip.

The wheel arch liner has an M6 clip nut which goes through a tag on the bumper spat. The arch liner also has a slot which goes around the edges where the two spats meet.

DaveMcT said:

There is no clip in there. The bumper arch clips under the wing arch. That's it. So to you

Click to expand...

but it clearly shows a clip in the picture!

it may not be fitted from the factory, but it certianly looks the part and should help in the fitment of the arch trim as it is a bit poor.

dac69er said:

but it clearly shows a clip in the picture!

it may not be fitted from the factory, but it certianly looks the part and should help in the fitment of the arch trim as it is a bit poor.

Click to expand...

Have a look at the parts diagram

I can't seem to find a decent online parts catalogue anywhere, any ideas?

Wazzzer said:

I can't seem to find a decent online parts catalogue anywhere, any ideas?

Click to expand...

Fiatdalys
Great online cat

https://www.fiatdalys.lt/en/catalog/diagrams/707/2Q/0/0/M17/0/GD

https://www.fiatdalys.lt/en/catalog/parts/707/26/1/1/2Q/0/0/M17/0/GD/front-bumper