20170329_140234.jpg

Panda (Classic) I'm Back With The Panda 750L 1991

Introduction

My Story

Hi folks, its been a while since I had a panda after selling Purple Haze the Parade and Engelbert the Sisley (to Freebo ) the former I sold because my wife was pregnant and I felt (wrongly) that I needed a bigger (and to my mind at the time safer) car for ferrying my son and wife around in.

A very short while after I sold the pandas I developed Generalised Anxiety Disorder, I have had it now for nearly 2 years and I am FINALLY starting to get better it seems. The paranoid thoughts that I was going to put my son and wife in danger in the panda were part of this in my opinion.

Selling the Parade was a huge mistake on my part (and as older forum members were know it was subsequently written off in a low speed crash by the new owner) though the Sisley is much better off with Freebo as he appreciates the 4x4's (they are not to my taste on the open road but are amazing in a field IMHO) and I have regretted it. I have not had a car for some time now partially due to my illness and partially due to the fact I have lost my job due to my illness, though as forum members will remember I am a Youtuber too.

Fast forward to last night and I was browsing the forum and I came across an ad for a 750L in Glasgow (I am in Prestwick), and it was free but had to be collected today or in 2 weeks time. Being the impatient (and obviously anxious) type, I arranged through a friend of a friend to have it collected today. It arrived at 1pm and I am utterly flabbergasted at the condition. Out of my 3 Pandas it arrived in the best condition IMHO. So I am very thankful to the seller but forgotten their forum name cos the ad has been deleted! So thanks Ian (I am sure you are reading)

Ian reported that it has an oil leak under pressure, and as far as I can tell so far the problem is the oil filter housing which would be a super easy fix :) the rear arches need cut out at the base and refabricated, though this is not a huge job to my knowledge and I have a friend who is potentially going to do that for me all being well. Aside from that as far as I can tell it just needs new seatbelts, a new passenger rear brake cluster, new door locks, the front seat cover sewed up or renewed (the rest is immaculate) and some rust spots in the usual places taken care of. And a good service just to be on the safe side!

I couldn't be happier at this point and I cant wait to share my progress on here and Youtube for you all to see :)

Cameron

I am sure I will be asking for your guidance nearer the time :)

Pity you are so far North otherwise could lend a hand! We are aiming to move North at some stage but recon your car will be completely finished before then!

Plenty of more experienced advisors on here than me for Panda pointers though:D.

Screws and plugs arrived today for the door pocket, might even get it fitted this weekend, though playing about with alternators hopefully.
 
Pity you are so far North otherwise could lend a hand! We are aiming to move North at some stage but recon your car will be completely finished before then!

Plenty of more experienced advisors on here than me for Panda pointers though:D.

Screws and plugs arrived today for the door pocket, might even get it fitted this weekend, though playing about with alternators hopefully.
just today?? I sent it ages ago!
 
Autoglym Ultimate Screenwash is on sale in halfords atm (may be a system error as the sale ended last week in my store and the shelf said £8) at £2.95. Grab it while you can!

I used the 3 litre reservoir capacity as follows: 300ml (of 500ml bottle) to 2700ml of water as per the optimum bottle suggestion of a dilution of 1:9

A wee treat for the old girl (who I shamefully havent named yet)
 
tightened the alternator belt further today, seems to have cured the sqealing. was surprised how much i could move the alternator down, i clearly didnt do a good job first time around at all.

also pressure washed in the wheel arches, another few steps towards my goal (whatever that is)

just enjoying improving the wee motor
 
So I have removed the rear bumper and tidyed up the rust and paint etc quite happy with the rear, but the side brackets are non existant. VmanC is kindly fabricating some new ones I can bolt on and then I can tidy up as best I can and get the bumper mounted properly :) also need to resolder one of the light connections and I have new nuts and bolts coming for the sides too.
 
The bolt on T shaped piece makes sense, no need to miss out on any Panda driving:D. You could get it electro-plated and coated to prevent it rusting again where the old one went. Is this what Vernon is making up for you?
 
The bolt on T shaped piece makes sense, no need to miss out on any Panda driving:D. You could get it electro-plated and coated to prevent it rusting again where the old one went. Is this what Vernon is making up for you?
Yeah Vernon has made them for me :) i dont have anywhere who would do that anywhere near me, home methods will have to suffice!

Cheers man im excited to get them and get the bumper looking good
 
Cam to get that bumper looking perfect too tip is to use black plastic trim and bumper spray we used it for all the plastic parts on Brian.
Even Freddy thought we'd bought new bits it's very very good faded dash components and a complete change from Sisley grey/blue to black spot on didn't flake or require undercoat or primer !!
 
Back
Top