Technical Tipo Engine head

[INsantiy]

Hi,
I would like to know the diffrence between the 1.4 head and 1.6 head
camshaft degress , intake ports ect.....
can i put a 1.6 head on 1.4 engine? , would it make any diffrence?!

 

[TipoMania]

Hello,if you want to put the cam form 1.6 to your 1.4 and that's it.You wrong,you will also need reprogramming the ecu cause in high rpm you run out of fuel.There is a Colombo&Briani cam on the market for the 1.4 with the chip for your ecu.Anyway here are the timings of the 1.4 and 1.6 cams:

160.A1.046(1.4L) 159A3.048(1.6)
Inlet Opens 7 (24) 6
Inlet Closes 35 (76) 46

Exhaust Opens 37 (70) 47
Exhaust Closes 5 (18) 7

In () are the timming from the colmbo&briani cam,the choise is yours.....

 

[sumplug]

Hello,if you want to put the cam form 1.6 to your 1.4 and that's it.You wrong,you will also need reprogramming the ecu cause in high rpm you run out of fuel.There is a Colombo&Briani cam on the market for the 1.4 with the chip for your ecu.Anyway here are the timings of the 1.4 and 1.6 cams:

160.A1.046(1.4L) 159A3.048(1.6)
Inlet Opens 7 (24) 6
Inlet Closes 35 (76) 46

Exhaust Opens 37 (70) 47
Exhaust Closes 5 (18) 7

In () are the timming from the colmbo&briani cam,the choise is yours.....

The columbo cam is useless unless you gasflow the head. Unless a lot of work is done to the head and a higher compression is used with improved induction and exhaust, then stick with the standard cam.
1400 and 1600 is same cam as standard. Only difference on the head, is the exhaust valve on the 1600 is slightly bigger. Yes, 1600 head will fit 1400.

Andy.

 

[INsantiy]

Thanks, i dont have ECU
does the 1.6 head will make any diffrence?!
power,Acclarte..something?!
and i have another questiuon , if i will put an 1.6 carb will it make diffrence?

 

[sumplug]

Thanks, i dont have ECU
does the 1.6 head will make any diffrence?!
power,Acclarte..something?!
and i have another questiuon , if i will put an 1.6 carb will it make diffrence?

Carb is a Weber TLDE, and is very similar on the 1.4 and 1.6. Fitting the head and carb will give you virtually no power difference. What you need to do, is gasflow the 1.4 head, skim it to raise compression, rejet the carb, fit a free flow airfilter and fit a better exhaust.

Andy.

 

[INsantiy]

Thanks=)

 

[dazzo666]

Or put a 1.6 in your car.....

 

[INsantiy]

It isn't so esay to put a 1.6 engine you have to register the engine
and it is a problem =/

 

[sumplug]

It isn't so esay to put a 1.6 engine you have to register the engine
and it is a problem =/

You could bore the block out and fit 1600 pistons.

Andy.

 

[fiat1100d]

160.A1.046(1.4L) 159A3.048(1.6)
Inlet Opens 7 (24) 6
Inlet Closes 35 (76) 46

Exhaust Opens 37 (70) 47
Exhaust Closes 5 (18) 7

Do you happen to have cam information about the 159 A3.000 engine too? That is the 1581 cc 86 HP unit fitted on the Tempra 1600

What improvement there would be by fitting a 128 Rally camshaft? I have been told it has 24° 68° / 64° 28° and a lift 1 mm higher.

Thanks!

 

[sumplug]

Do you happen to have cam information about the 159 A3.000 engine too? That is the 1581 cc 86 HP unit fitted on the Tempra 1600

What improvement there would be by fitting a 128 Rally camshaft? I have been told it has 24° 68° / 64° 28° and a lift 1 mm higher.

Thanks!

cam timing for 1600 is 7/35/37/5

Andy.