Whichever is cheapest, they're pretty low pressure so it doesn't matter too much for the breathers 
Technical What do i do with this?
- Thread starter AgnessGP
- Start date
Currently reading:
Technical What do i do with this?
OP
OP
right, everything fits except the plastic t -piece.
Because its low pressure, would i be able to fasten it to the alloy t-piece using some sort of tape or glue?
thanks in advance
Because its low pressure, would i be able to fasten it to the alloy t-piece using some sort of tape or glue?
thanks in advance
Did you not get any 25mm rubber tubing?
Edit: Oh and PICS
Edit: Oh and PICS
OP
OP
its cost me £75 already, if i could get away with not buying any it would be brill so thought id try.
plus im sure i could get hold of some if need be
what you reckon to the plastic t piece?
plus im sure i could get hold of some if need be
what you reckon to the plastic t piece?
Last edited:
OP
OP
im trying to send some pics but bluetooth on laptop is extremely touch and go
You could (if you wanted) chop the original crankcase breather hose to fit, or is it not long enough?
OP
OP
hold your horses mate iv only built it up in living room lol!
Tomorrow is fitting day I think, still need some brackets or something
any suggestions?
Tomorrow is fitting day I think, still need some brackets or something
any suggestions?
Last edited:
Tomorrow I will be connecting the crankcase breather to the gsr if your all interested in knowing where it goes.
OP
OP
when you doing it mate. Maybe give me a ring tomorrow!
Eklipze: i cant chop the crankcase breather because i need the plastic t-piece to fit in order to fit the manifold breathrr inlet on
Eklipze: i cant chop the crankcase breather because i need the plastic t-piece to fit in order to fit the manifold breathrr inlet on
OP
OP
or did you mean chop a bit off and use it.to connect the.two t-pieces
OP
OP
i am mate but not got the.petrol to get there no idea what to buy to secure the bmc on?
no idea what to buy to secure the bmc on?
Ahh right, no worries, depending where it sits you can probably just secure it with some strong zip ties. I've got about 10 of the buggers holding my kit up to stop it fouling on the clutch actuator arm
OP
OP
apologies but do you mean tie wraps?
not taking the mick if you call them something different just checking we mean the same thing
not taking the mick if you call them something different just checking we mean the same thing
Those things
- Joined
- Oct 30, 2010
- Messages
- 1,078
- Points
- 227
lol
- Joined
- Oct 30, 2010
- Messages
- 1,078
- Points
- 227
OP
OP
hahaha thats just me mate ill admit that lol
edit: eklipze ill prob be fitting today but had a heavy night last night so waiting until I can legally drive
edit: eklipze ill prob be fitting today but had a heavy night last night so waiting until I can legally drive
OP
OP
think i might have been better off buying the GSR for sale on here.
because the plastic -tpiece doesnt fit i've just been to a motorfactors that sell t-pieces. Only problem is they only sell them with the same size outlet to the size of the piece eg. a 2 mm piece will have a 2mm outlet.
also, even if i get a t-piece to fit the pipes, the other end will then be too small to fit into the alloy t-piece unless i can put a washer or something round it.
because the plastic -tpiece doesnt fit i've just been to a motorfactors that sell t-pieces. Only problem is they only sell them with the same size outlet to the size of the piece eg. a 2 mm piece will have a 2mm outlet.
also, even if i get a t-piece to fit the pipes, the other end will then be too small to fit into the alloy t-piece unless i can put a washer or something round it.
Last edited:
