I am in need of an passenger side tripod joint (or tripod cup) and I need to know the number of teeth that the tripod joint has, since the store I want to buy it from ,autodoc.se, has both 25,21 and 26 teeth versions.
Thanks for any help!

2008 Fiat bravo 120t, 190k km and counting,

Looks like im going to replace the entire driveshaft. Ill update this thread when I disasemble the old one and find the number of teeth for anyone with the same problem as me.

Update!
I took apart the worn driveshaft and found that the tripod has 26 teeth. (See pictures)

However: The driveshaft I ordered is diffrent from my Fiat. My driveshaft has a rollerbearing that is 68mm, the one I got is not 68mm, and therefor it will not fit. I've returned it and now im waiting for the correct one to be back in stock.


https://imgur.com/5Y1uGPp

This is how it is supposed to look:




The one I bought looks like this:

from Fiat the long driveshaft comes in 2 pieces: 1. same part as the short driveshaft, and 2.a longer cup.
have a look in eper.

So the driveshaft is the same on both sides, just with a longer cup? Does that mean that the tripod joints are the same aswell?

BlueBravoGuy said:

So the driveshaft is the same on both sides, just with a longer cup? yes

Click to expand...

I have them by my feet under my desk, as i type... haven't gotten around to installing them.

BlueBravoGuy said:

Does that mean that the tripod joints are the same as well?

Click to expand...

I can't confirm it, but I'm sure they are, i've purchased tripods in the past... they never mentioned right/left... same part.

Sounds promising, hopefully I'll be back in my little bravo by early next week! :

Re: Number of teeth tripod joint. SOLVED

It's Alive!
The driveshaft finally got back in stock, so I immediately ordered it and third time's a charm, it was right!

Feels so good to be back in my bravo after a MONTH of old renault and volvo driving.

Feel free to ask any question about changing the driveshaft on the right hand side.

BlueBravoGuy said:

Re: Number of teeth tripod joint. SOLVED

It's Alive!
The driveshaft finally got back in stock, so I immediately ordered it and third time's a charm, it was right!

Feels so good to be back in my bravo after a MONTH of old renault and volvo driving.

Feel free to ask any question about changing the driveshaft on the right hand side.

Click to expand...

Now i can confirm what i said earlier. it works, it's installed in the car, so much better.

I need both driveshaft for my Bravo '07 150cv Sport 6 Manual. I think that actual driveshafts are for 120cv Bravo, because they went bad in almost 5-6 months after I purchased the car in 2021, and those looked like new when i saw underneath of the car. I have to find those for 150cv '07 Bravo and it is really hard and expensive.

itechtime said:

I need both driveshaft for my Bravo '07 150cv Sport 6 Manual. I think that actual driveshafts are for 120cv Bravo, because they went bad in almost 5-6 months after I purchased the car in 2021, and those looked like new when i saw underneath of the car. I have to find those for 150cv '07 Bravo and it is really hard and expensive.

Click to expand...

So what i found out is that there are 2 different driveshaft, one has a small and wide bearing (62mm diameter) (only on right side) and the other is thin and tall (68mm diameter) my 120 t-jet (late 2007 model) had the 68mm one. I dont know if they differ between the 120 and 150 or why there are 2 versions. I dont know if you can check the diameter without removing it, which is a lot of work, but not difficult.