Technical I have change climate control on my Stilo Abarth -02

Currently reading:
Technical I have change climate control on my Stilo Abarth -02

Jonny Wallin

New member
Joined
Dec 16, 2009
Messages
11
Points
2
Hi all!

Write to this excellent forum from Sweden. I have change climate control on my Stilo Abarth -02 because it was broken.
Now the new one works. But the milage is flashing.
Then I bought Multiecuscan software 1,8 and tries to do a Proxy alignment.

But it always get failed on Climate Nod and the rest is succeed. I have tryed many times and failed every time.

Below you can see my logg:

Please, can someone help me, how to do? :worship:

Best Regards Jonny Wallin

Reading CAN configuration data ...
CAN CONFIGURATION DATA:
01 02 1F DF 01 02 1F DF 00 00 08 01 00 00 08 01 00 00 00 00
01 02 1F DF 01 00 04 09 01 02 1F DF 01 00 04 09 01 00 00 09
30 34 31 39 32 30 30 30 32 38 34 54 45 52 4D 3A 30 38 20 20 20 20 02 11 13 DF 1F 02 01 09 04 00 01 81 05 00 00 00 84 16 07 00 02 3C 06 00 00 00 00 00 00 00 23 60 61
CURRENTLY CONFIGURED CAN MODULES:
Body Computer Node (NBC)
Engine Control Node (NCM)
Electric Steering Node (NGE)
Dashboard Node (NQS)
Steering Wheel Controls Node (NVO)
Brake System Node (NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Boot Node (NVB)
Climate Control Node (NCL)
Automatic Transmission Node (NCA-NCR)
Steering Angle Sensor Node (NAS)
Passenger Door Node (NPP)
Parking Sensor Node (NSP)
CURRENTLY AVAILABLE CAN MODULES:
Body Computer Node (NBC)
Engine Control Node (NCM)
Electric Steering Node (NGE)
Dashboard Node (NQS)
Steering Wheel Controls Node (NVO)
Brake System Node (NFR)
Info-Telematic/Convergence Node (NIT/NCV)
Driver Door Node (NPG)
Boot Node (NVB)
Climate Control Node (NCL)
Automatic Transmission Node (NCA-NCR)
Steering Angle Sensor Node (NAS)
Passenger Door Node (NPP)
Parking Sensor Node (NSP)
CAN MODULES THAT REQUIRE EOL PROGRAMMING:
Body Computer Node (NBC)
Dashboard Node (NQS)
Climate Control Node (NCL)
Parking Sensor Node (NSP)
2014-03-19 18:10:24
CONNECTED TO:
Fiat Stilo Selespeed
CAN Setup / PROXI Alignment Procedure
--------------------------------------------------------------

CURRENTLY CONFIGURED CAN MODULES::
Body Computer Node (NBC):
Engine Control Node (NCM):
Electric Steering Node (NGE):
Dashboard Node (NQS):
Steering Wheel Controls Node (NVO):
Brake System Node (NFR):
Info-Telematic/Convergence Node (NIT/NCV):
Driver Door Node (NPG):
Boot Node (NVB):
Climate Control Node (NCL):
Automatic Transmission Node (NCA-NCR):
Steering Angle Sensor Node (NAS):
Passenger Door Node (NPP):
Parking Sensor Node (NSP):
:
CURRENTLY AVAILABLE CAN MODULES::
Body Computer Node (NBC):
Engine Control Node (NCM):
Electric Steering Node (NGE):
Dashboard Node (NQS):
Steering Wheel Controls Node (NVO):
Brake System Node (NFR):
Info-Telematic/Convergence Node (NIT/NCV):
Driver Door Node (NPG):
Boot Node (NVB):
Climate Control Node (NCL):
Automatic Transmission Node (NCA-NCR):
Steering Angle Sensor Node (NAS):
Passenger Door Node (NPP):
Parking Sensor Node (NSP):
:
CAN MODULES THAT REQUIRE EOL PROGRAMMING::
Body Computer Node (NBC):
Dashboard Node (NQS):
Climate Control Node (NCL):
Parking Sensor Node (NSP):

EXECUTING ADJUSTMENT...
PROXI ALIGNMENT PROCEDURE
Writing CAN configuration data ...
Writing to module: Body Computer Node (NBC) SUCCESS!
Writing to module: Dashboard Node (NQS) SUCCESS!
Writing to module: Climate Control Node (NCL) FAILED! - Unknown error
Writing to module: Parking Sensor Node (NSP) SUCCESS!
FAILED TO EXECUTE
Climate Control Node (NCL) FAILED! - Unknown error
 
Last edited:
Hi all!

Write to this excellent forum from Sweden. I have change climate control on my Stilo Abarth -02 because it was broken.
Now the new one works. But the milage is flashing.
Then I bought Multiecuscan software 1,8 and tries to do a Proxy alignment.

But it always get failed on Climate Nod and the rest is succeed. I have tryed many times and failed every time.

Below you can see my logg:

Please, can someone help me, how to do? :worship:

Best Regards Jonny Wallin

Hi Jonny,

Try this...

Stilo eLEARN said:
CLIMATE CONTROL SELF-LEARNING PROCEDURE

The AUTO and MONO buttons must be pressed simultaneously within 40 seconds of the ignition being turned to the ON position in order to active this procedure.

A few seconds later a figure will appear on the display (in place of the driver's side set temperature) which will count down to indicate the time remaining before the start of the procedure. At the same time (i.e. whilst the count down is taking place) the previous self-learning status is signalled on the passenger temperature setting:

'1' flashes if the previous self-learning procedure failed.
'0' indicates that the previous self-learning procedure was successful.

This procedure is not carried out if at least one of the above mentioned buttons is released whilst the figure on the left hand side is not zero (this is designed to check the outcome of the previous self-learning procedure).

Exiting the procedure zeroes the 40 second counting period from when the ignition is switched ON, to allow the procedure to be repeated without having to switch the ignition OFF.

Each time a new control unit is fitted, the flap actuator learning test must be carried out using the diagnostic equipment and the unit must be personalized through programming.

i think the key is the part i have highlighted in Bold... if you run MES then go into Climate Control>Marelli Climate Control>Adjustments you should see an option for the 'Flap Actuators Learning' run this learning test and then try the Proxi Alignment again... come back to tell us if it worked or not ;)

flap learn.jpg
 
Last edited:
Hi!
Thanks for your try to help me.
I have tried to follow your steps. But when I connect Multiecuscan to the climate nod, I can read all data of software, production date and so on,
and then I have connection to the Pc :)

But when I try to do the flap actuator learning test, it says failed directly :confused:
I can hear the flaps trying to do someting.

Do you have some more ideas?

This is the log:

ECU ISO Code: 34 83 04 01 91
2014-03-20 19:53:32
CONNECTED TO:
Fiat Stilo Selespeed
Marelli climate control
--------------------------------------------------------------

ECU ISO code: 34 83 04 01 91
FIAT drawing number: 735319258
Hardware number: 03600000200
Hardware version: 05
Software number: 04600000002
Software version: 0600
Homologation number:
ECU programming date: 10/08/2001

EXECUTING ADJUSTMENT...
Flap actuators learning
COMPLETED
Failed

EXECUTING ADJUSTMENT...
Flap actuators learning
COMPLETED
Failed

Regards Jonny
 
Last edited:
Hi again!

Is it anyone out there who has done this with success?
Or is it not in function in the software

I have search on the forum and I can see that other Stilo user also seems to have problem to do it.


Best Regards Jonny
 
Back
Top